Caratteristiche
☑ 4.0-inch Inside/Outside CCAW (copper-clad aluminum wire) voice coil
☑ 3000 Watt continuous program power handling
☑ 98.5 dB Sensitivity
☑ 25 Hz - 1 kHz Frequency range
☑ Hypervented magnetic structure for minimum power compression
☑ Triple roll surround and exponential cone geometry
☑ Single aluminum demodulation ring
The LN19S400 is a 19-inch extended low-frequency transducer designed with high excursion piston capabilities, perfect for vented enclosures where power and low-frequency extension are priorities. One of the key highlights of the transducer is its ultralight CCAW (copper-clad aluminum wire) voice coil, which is configured in a 4.0-inch, 4-layer inside-outside voice coil with fiberglass former material. The ultra-long excursion moving mass (65mm/2.5" safe peak-to-peak) with high power and fast acceleration capabilities. Employing a cone assembly loaded with fibers and featuring a generous triple-roll surround, the LN19S400 is engineered to decrease flux modulations and enhance transient response. The Hyper-Vented dual-forced air system enhances voice coil ventilation, effectively minimizing power compression.
RCF LN19S400
482,21 €
Tasse incluse
Spedito entro 5/7 Giorni
Caratteristiche
☑ 4.0-inch Inside/Outside CCAW (copper-clad aluminum wire) voice coil
☑ 3000 Watt continuous program power handling
☑ 98.5 dB Sensitivity
☑ 25 Hz - 1 kHz Frequency range
☑ Hypervented magnetic structure for minimum power compression
☑ Triple roll surround and exponential cone geometry
☑ Single aluminum demodulation ring
The LN19S400 is a 19-inch extended low-frequency transducer designed with high excursion piston capabilities, perfect for vented enclosures where power and low-frequency extension are priorities. One of the key highlights of the transducer is its ultralight CCAW (copper-clad aluminum wire) voice coil, which is configured in a 4.0-inch, 4-layer inside-outside voice coil with fiberglass former material. The ultra-long excursion moving mass (65mm/2.5" safe peak-to-peak) with high power and fast acceleration capabilities. Employing a cone assembly loaded with fibers and featuring a generous triple-roll surround, the LN19S400 is engineered to decrease flux modulations and enhance transient response. The Hyper-Vented dual-forced air system enhances voice coil ventilation, effectively minimizing power compression.
close
| Specifiche generali | Diametro Nominale | 19 inch / 483 mm |
|---|---|---|
| Impedenza nominale (ohm) | 8 ohm | |
| Potenza musicale (watt) | 3000 W | |
| Potenza | 1500 W | |
| Sensibilità (dB) | 98.5 dB | |
| Gamma di frequenza | 25 - 1000 Hz | |
| Diametro effettivo del pistone | 410 mm / 16.14 inch | |
| Escursione max prima della rottura | 59 mm / 2.32 inch | |
| Impedenza Minima (ohm) | 6.2 ohm | |
| Diametro Bobina | 4.0 inch / 102 mm | |
| Materiale di avvolgimento della bobina | Aluminum | |
| Lunghezza della bobina | 42 mm / 1.65 inch | |
| Numero di strati | 4 | |
| Strati bobina (tipologia) | inside/outside | |
| Spessore piastra superiore | 16 mm / 0.63 inch | |
| Design del cono | Curved | |
| Materiale del surround | Polycotton | |
| Design del surround | Triple roll | |
| Magnete | Neodymium | |
| Struttura Magnetica Hypervented | Yes | |
| Aerazione Dual-Force | Yes | |
| Materiale Anello di Demodulazione | Aluminum | |
| Anelli di demodulazione | 1 | |
| Spider | 4 | |
| Anello di demodulazione | Yes | |
| Parametri di Thiele & Small | Frequenza di Risonanza (Fs) (Hz) | 32 Hz |
| Resistenza (Re) (ohm) | 4.70 ohm | |
| Fattore di merito meccanico (Qms) | 4.00 Qms | |
| Fattore di merito elettrico (Qes) | 0.27 Qes | |
| Fattore di qualità totale (Qts) | 0.26 Qts | |
| Fattore Bl (Bl) (T x m) | 32.00 T x m | |
| Massa mobile effettiva (Mms) g | 296.0 g | |
| Volume equivalente alla cedevolezza (Vas) (litri) | 204.0 liters | |
| Area del pistone effettiva (Sd) (m2) | 0.132 m2 | |
| Massima escursione lineare (Xmax) (mm) | 17 mm | |
| Induttanza della bobina @ 1 kHz (Le1k) (mH) | 3.40 mH | |
| Efficienza Half-Space (Eff) (%) | 2.37% | |
| Informazioni di montaggio | Diametro complessivo | 480 mm / 18.9 inches |
| Diametro esterno vite | 460-462 mm / 18.11-18.19 inch | |
| Diametro foro vite | 7 mm / 0.28 inch | |
| Foro montaggio anteriore al pannello | 446 mm / 17.56 inch | |
| Alloggiamento posteriore | 446 mm / 17.56 inch | |
| Volume occupato dal driver | 10 liters / 0.39 ft3 | |
| Conformità agli standard | Standard di sicurezza | CE compliant |
| Dimensioni / Peso | Altezza | 232 mm / 9.13 inches |
| Diametro | 480 mm / 18.9 inches | |
| Diametro di taglio | 446 mm / 17.56 inches | |
| Peso | 10.2 kg / 22.49 lbs | |
| Informazioni di spedizione | Altezza imballaggio | 290 mm / 11.42 inches |
| Larghezza imballaggio | 505 mm / 19.88 inches | |
| Profondità imballaggio | 515 mm / 20.28 inches | |
| Peso imballaggio | 10.9 kg / 24.03 lbs |
11100167
Scheda dati
- Pollici
- 19